Home > Parts > Odds n Ends
Choose a sub category:
Specials - Prefits and fluted barrels
If I cant figure out where else to put, it might be in here...
Sort By:
Page of 2
Thread Protector SS 5/8-24tpi
Thread Protector SS 5/8-24tpi
Usually Ships in 24 Hours
Our Price: $35.00
24 in stock!

5/8-24 Stainless thread protector, .995 OD, 1.00 long, with a .3 dia blind hole. will accept a .700" tenon, approx .100" of thread relief with a .125 wide slot for applying torque via flat tool of you choice (the back of your pocket knife)

**** This is designed to be turned and blended to barrel diameter. ****
more info
Thread Protector SS 1/2-28tpi
Thread Protector SS 1/2-28tpi
Usually Ships in 24 Hours
Our Price: $35.00
11 in stock!

1/2-28 Stainless thread protector, .995 OD, 1.00 long, with a .3 dia blind hole. will accept a .700" tenon, approx .100" of thread relief, .125 wide slot for applying torque via flat tool of you choice (the back of your pocket knife)

**** This is designed to be turned and blended to barrel diameter. ****
more info
Thread Protector SS 3/4-24tpi
Thread Protector SS 3/4-24tpi
Usually Ships in 24 Hours
Our Price: $35.00
21 in stock!

3/4-24 Stainless thread protector, .995 OD, 1.00 long, with a .3 dia blind hole. will accept a .700" tenon, approx .100" of thread relief, .125 wide slot for applying torque via flat tool of you choice (the back of your pocket knife)

**** This is designed to be turned and blended to barrel diameter. ****
more info
Foundation Butt spacer .475"
Foundation Butt spacer .475"
Usually Ships in 24 Hours
Our Price: $35.00
**OUT OF STOCK**

Aluminum .475" butt spacer for the Foundation stock length of pull system, this can replace the provided micarta spacers that come with the stock.  Weighs 5.2 oz.  *** May require some fitting for a perfect fit as Foundation butt stocks can vary*** more info
Bugholes BugLug Precision Ground Stainless .250" Recoil Lug 1.065"
Bugholes BugLug Precision Ground Stainless .250" Recoil Lug 1.065"
Usually Ships in 24 Hours
Our Price: $40.00
5 in stock!

Bugholes BugLug Precision Ground Stainless .250" Recoil Lug with 1.065" bore. Pin hole for lug indexing is a blind 3/32" hole for a more finished look. Will fit Holland lug alignment tool. more info
Bugholes BugLug Precision Ground Stainless .250" Recoil Lug 1.077"
Bugholes BugLug Precision Ground Stainless .250" Recoil Lug 1.077"
Usually Ships in 24 Hours
Our Price: $40.00
3 in stock!

Bugholes BugLug Precision Ground Stainless .250" Recoil Lug with 1.077" bore for a larger diameter trued tenon. Pin hole for lug indexing is a blind 3/32" hole for a more finished look. Will fit Holland lug alignment tool. more info
Bugholes multi cal shell plate for Dillon 550
Bugholes multi cal shell plate for Dillon 550
Usually Ships in 24 Hours
Our Price: $50.00
10 in stock!

Bugholes multi cal shell plate for single stage loading on the Dillon 550 reloading press. This shell holder has 223, 308, mag, and Lapua stations on each shell plate. Size all your brass at one time at the sizing station then index over to your seating station to seat in another operation. If youre loading single stage you'll never need to change shell plates again. Made from 4140 pre-hard chrome moly steel with a black nitrided finish
more info
Bugholes Lug Alignment Tool
Bugholes Lug Alignment Tool
Usually Ships in 24 Hours
Our Price: $50.00
2 in stock!

Bugholes Lug Alignment Tool for Remington 700 and 1.350" diameter Rem 700 clones.  Hard coat Anodized finish, designed to hold our Buglugs and Holland taper lugs.  Includes 1/4-28 cap screw and washer. more info
AIAX Bag Rider black
AIAX Bag Rider black
Our Price: $90.00
19 in stock!

Rear bag rider for the AIAX, AXSR, AT-X, and MRAD rifle buttstock. 6061 Aluminum with hard coat black anodized finish
The bag rider is 5" long, .800 wide, and extends 1.25 below the rear Pic rail to be flush with the end of the butt pad.
more info
BugEye scope turret magnifier
BugEye scope turret magnifier
Our Price: $140.00
**OUT OF STOCK**

The F.O.G turret magnifier AKA BugEye is a highly adjustable system designed for 34mm scope tubes hold a quick attach magnifying lens in front of your scope turret. It enlarges the small numbers and click graduations on today's high-travel rifle scopes reducing errors and eye strain.

If you have a 30mm scope both Badger and LaRue offer 1" to 34mm conversion sets that will allow you to use our BugEye.
more info